Skip to content

See every repair stage in pictures. Talk to the shop

(559) 315-3662
(559) 315-3662
Technician pulling a chain on a red frame machine tower attached to the crushed front end of a gray sedan clamped on the bench in a body shop bay

ServicesFrame Straightening

Frame Straightening in Huron

A hard hit can shift your car's structure even when the outside looks fine. We measure your vehicle against factory dimensions, pull it back into spec, and show you photos and numbers from before, during and after the repair.

What frame straightening fixes

Most cars today don't have a separate frame. The body itself is the structure, called a unibody, and a collision can push it out of shape by a fraction of an inch. That's enough to throw off how doors close, how the wheels sit and how the car handles. Trucks and some SUVs still ride on a full frame, and those can bend, twist or sag after a hit.

We put your vehicle on a frame rack, measure key points underneath, and compare them to the factory numbers for that make and model. Then we pull the structure back slowly and measure again until it's where it should be. Our shop is I-CAR Gold certified.

You see the whole thing. We photograph the damage we find, the setup on the rack and the final measurements, so you know what was bent and what we did about it.

What the work includes

Full structural measurement
We check reference points across the underbody, not just the corner that got hit. A front impact can move the rear rails too.
Controlled pulls on a frame rack
The vehicle is anchored at several points and pulled with chains and towers in small steps. We measure between pulls so we don't overcorrect.
Section or replace when needed
Some high-strength steel isn't meant to be heated or pulled past a certain point. If a rail or support is too far gone, we tell you and replace that section instead of forcing it.
Before and after records
You get photos and the measurement readouts from the start and the finish. Your insurance adjuster can use them too.
Alignment and system checks
Once the structure is right, the wheels get aligned. If your car has cameras or radar sensors in the bumper or windshield, we let you know whether they need calibration after the repair.

Signs your frame may be bent

  • Doors or hood don't line up

    Gaps that are wider on one side, or a door that suddenly needs a slam to latch, often mean the body has shifted.

  • The car pulls after an accident

    If it drifts left or right and an alignment doesn't fix it, the wheel mounts may have moved.

  • Tires wearing unevenly

    Fast wear on the inside or outside edge of one tire can point to a bent suspension mount or rail.

  • Trunk or tailgate won't close right

    A rear hit can rack the opening so the latch no longer meets.

  • New noises or creaks

    Rattles, wind noise or creaking over bumps after a collision are worth a look underneath.

  • Visible kinks underneath

    Wrinkled metal on a rail or crossmember is a clear sign. Many cars that ride rough farm roads around the valley hide this until someone gets under them.

How a frame repair goes

  1. 1

    Inspection and photos

    You bring your vehicle to our shop. We look it over, get it on the lift and photograph the damage before anything is touched.

  2. 2

    Measure and write the estimate

    We take the first set of measurements and write up what needs to be pulled, sectioned or replaced. You see the estimate and what we found before we start.

  3. 3

    Pull and re-measure

    The car goes on the rack. We pull in stages and check the numbers after each one until every point is back in spec.

  4. 4

    Finish the repair

    With the structure right, we move on to panels, paint and alignment. Many frame jobs lead into collision repair or paint and refinishing on the same visit.

  5. 5

    Walk-through at pickup

    We go over the final measurements and the before-and-after pictures with you, and you take the records home.

Shop estimator with a clipboard points out marked dents on a gray SUV's front fender to a customer on a concrete body shop lot, with repair bays behind

What moves the cost

There's no flat price for frame straightening. It depends on how far the structure moved and where. We give you a written estimate after we measure, and if we find more once the car is on the rack, we show you what turned up and talk to you before doing extra work.

How far it's out of spec
A few millimeters at one corner is a short pull. Damage that runs through the floor pan or into the rear takes more setup and more time.
Pull versus replace
Straightening a rail costs less than cutting out and welding in a new section. Some steels don't leave a choice.
Vehicle type
A full-frame pickup and a unibody sedan are set up and measured differently, and parts prices vary a lot by make.
Related damage
Suspension parts, sensor calibration and the body and paint work that follows all add to the total. Your insurance claim may cover much of it.

Frame straightening questions

Something not covered here? (559) 315-3662

Is a car safe to drive after frame straightening?

Yes, when the structure is measured back to factory dimensions and any parts too damaged to pull are replaced. That's why we measure after every pull and give you the final numbers. If something can't be brought back safely, we tell you.

Will my car be considered totaled?

Frame damage alone doesn't mean a total loss. Insurers compare the repair cost to the car's value. We send the adjuster our measurements and damage records so the decision is based on real numbers.

How long does it take?

A light pull can be done in a day or two on the rack. Most of the time goes into the work that follows, like panels, paint and waiting on parts. We give you a time estimate once we've measured.

Can you tell if my frame is bent just by looking?

Not always. Small shifts don't show from the outside. Uneven gaps and pulling are clues, but measuring on the rack is the only way to know for sure.

Do you work with my insurance company?

Yes. We share the measurement records and pictures with your adjuster and explain what we found. Our insurance claims page covers how that process usually goes.

Freshly refinished dark blue pickup hood on a paint stand on a concrete shop lot, reflecting clouds, with the paint booth, repair bay and a damaged silver sedan behind

Get your car's structure checked

Bring it in and we'll measure it, photograph what we find and walk you through the estimate. Drivers come to us from Huron, Avenal, Lemoore and Coalinga.