
ServicesDent Repair
Dent Repair in Huron
We pull dings, creases and hail dents out of your car's panels. If the paint is still good, we fix it without repainting. If it isn't, we tell you why and show you the photos. You see the dent before, during and after.
Two Ways to Fix a Dent
Most dents fall into one of two jobs. Paintless dent repair works the metal back into shape from behind, so the factory paint stays put. It's the right call when the paint isn't cracked and the metal hasn't been stretched too far.
When the paint is chipped, the dent sits on a sharp edge, or the metal is creased hard, we pull it as close as we can, use a thin skim of filler, then prime and paint. That second route ties into our paint and refinishing work, and we blend the color into the panels next to it so it doesn't stand out.
We photograph the dent under shop lights before we touch it, so you can see what we see. Our shop is I-CAR Gold certified, and the techs who do this work know how today's panels are built and how far the metal can be pushed.
What the Repair Includes
- Inspection under lights
- We look at the panel under a reflection board. It shows low spots and high spots your eye misses in daylight.
- Photos at each step
- You get pictures of the dent as it came in, any trim or panels we removed to reach it, and the finished surface. If we find something else, like a cracked bracket behind a door, you see that too.
- Access and reassembly
- Some dents can only be reached by taking off a door panel, tail light or headliner trim. We remove it carefully, replace any one-time clips, and put it back the way it came out.
- Paintless work or refinish
- Rods, glue tabs and tap-down tools for paintless jobs. Filler, primer, paint and clear coat when the finish has to be redone.
- Final check and cleanup
- We check the panel under lights again, wipe it down and wash off any glue residue before you pick up your car.
Signs Your Car Needs Dent Repair
Door dings from parking
Small round dents along the doors and quarter panels. These are often good candidates for paintless repair if you get them fixed before rust starts.
A crease along a body line
Dents that run through a styled line or edge are harder to get right. Left alone, the paint along the crease can crack over time.
Cracked or flaking paint at the dent
Once the paint breaks, water can get to bare metal. That dent needs to be filled and refinished, not just pushed out.
Hail damage on the roof and hood
Lots of shallow dents across the top of your car. We count them, map them and record each one before giving you the estimate.
A dent that rattles or catches light
If you hear a loose part behind the panel, or the dent shows up every time the sun hits it, something may be bent behind it. We'll look and show you.
How a Dent Repair Goes
- 1
Call and bring it in
Give us a call and tell us what happened. Then bring your car to the shop so we can see the dent in person. Pictures on a phone don't show depth well.
- 2
Look, photograph, explain
We put the panel under lights, take photos and tell you whether it's a paintless job or a refinish job. You get a written estimate that lists the work line by line.
- 3
Do the repair
For paintless work, we reach behind the panel and push the metal out a little at a time, checking as we go. For a refinish, we pull the dent, apply filler, then prime, paint and clear coat. We take pictures at each stage.
- 4
Check it with you
When you pick up, we walk around the car with you and show the before and after pictures side by side. If something doesn't look right to you, we want to hear it then.

What Moves the Price
Dent repair pricing depends on the dent, not a flat rate. A shallow ding in the middle of a door is a quick job. A deep crease across a body line takes a lot longer. We'll explain what's driving your number when we hand you the estimate.
- Size and depth
- Bigger and deeper dents take more time to work out. Stretched metal may not go back without filler.
- Where the dent is
- Dents on edges, body lines or double-walled areas like roof rails are harder to reach and harder to finish clean.
- Paint condition
- If the paint is cracked, the job moves from paintless to refinish, which adds primer, paint, clear coat and blending.
- Panel material
- Aluminum panels, used on many newer trucks and cars, are stiffer and less forgiving than steel. They take more care and more time.
- Access and number of dents
- Removing trim, lights or headliners adds labor. Hail jobs are priced by how many dents there are and how big they are.
What Drivers Ask About Dents
Something not covered here? (559) 315-3662
Do some dents still need paint, even with paintless methods?
Yes. Pushing a dent out from behind only works when the paint is intact and the metal isn't stretched or folded into a sharp crease. Once we see your car, we'll say which kind of job it is and point to the spot on the panel that decides it.
How long will my car be at the shop?
A few door dings can be quick. A refinish job takes longer because primer, paint and clear coat each need time to cure. We'll give you a realistic timeline with the estimate.
If the panel gets repainted, will the color match?
We start from your car's paint code, spray test cards and hold them up to the panel in good light. Most of the time we blend the new color into the next panel over, so your eye doesn't catch where the repair stops.
Should I file an insurance claim for a dent?
Compare the repair cost with your deductible first. When those numbers are close, paying yourself is usually the easier path. Hail damage, or a dent someone else caused, is more often worth a claim. Our Insurance Claims page explains how we deal with your insurer, and they get the same photos you get.
What happens if you find damage behind the dent?
A hard hit can bend a bracket or break a clip you can't see from outside. If we find something like that, we pause, photograph it and call you before doing any added work. Bigger damage may turn the job into collision repair.

Got a Dent You Keep Looking At?
Bring your car in and we'll show you what we find under the lights. You'll know if it's a paintless job or a refinish before any work starts.